Saturday, September 1, 2012

Dive Theory - The Recreational Dive Planner (RDP)



You have got a shiny new Dive Computer so you can skip this step, erm no you can't, you need to know this part inside out. For your own safety and the safety of your students. Not to mention that as a dive professional you should set a good example and carry either the RDP or Wheel in your BCD pocket as a back up and also enforcing good diving practices. Unfortunately you can not take the erdpml underwater!

Compartments.

Where different tissues in the body release / absorb nitrogen at different rates.  Different parts of the body absorb and release nitrogen at different rates.  Blood and fat absorbs nitrogen easier and faster than muscle and bone.   Because of these different TISSUES, a decompression model has what we call THEORETICAL TISSUES or COMPARTMENTS.  Compartments are a way to measure / identify how fast or slow our body (and body tissues) absorb and release nitrogen.  FAST COMPARTMENT (blood) = absorb and release nitrogen fastSLOW COMPARTMENT (muscle and bone) = absorb and release nitrogen slowly.
Many dive computers now use the RGBM model which uses theoretical compartments as follows
2.5 mins Blood
5 min Brain
10 mins – 40 mins Spinal Cord
40 mins – 120 mins Skin
120 mins – 480 mins Muscle
480 mins + Joints etc

Halftimes

The rate at which the compartment absorbs / releases half capacity of nitrogen Each compartment has a halftime for the rate at which it absorbs and releases nitrogen A halftime is the time, in minutes, that it takes for a certain compartment to reach halfway from its initial tissue pressure to full pressure, (saturation), at a new depth.
Compartments “on gas” and “off gas” at the same rate. Hence the controlling compartment for surface intervals of the RDP is the 60 min compartment which takes 6 hours ,(6 x 60 mins) to reach it’s M value. This compartment also takes 6 hours to empty, there for a a repetitive dive is a dive made within 6 hours of a previous dive, allowing for the 60 min compartment to completely empty.
FAST (tissue) COMPARTMENT (gas washout) = SHORTER HALFTIME
SLOW (tissue) COMPARTMENT (gas washout) = LONGER HALFTIME
tissue halftimes


1.         After 5 minutes the compartment will go to halfway (half full)
2.         After 5 minutes more the half from the first 20 minutes will half again
3.         This halfing can only happen 6 times exponentially. The new compartment will always be considered saturated (full) when it reaches approx 98.6 percent.  To make it easier the tissue pressure can be expressed or called ‘metres'.

PRESSURE IN HALFTIME


COMPARTMENTS

1          Halftime (50%) in 18m = 9m of pressure (18 x 0.5)
2          Halftime (75%) in 18m = 13.5m of pressure (18 x 0.75)
3          Halftime (87.5%) in 18m = 15.75m of pressure (18 x 0.875)
4          Halftime (93.6%) in 18m = 16.8m of pressure (18 x 0.936)
5          Halftime (96.9%) in 18m = 17.4m of pressure (18 x 0.969)
6          Halftime (100%) in 18m = 18.0m of pressure
Example:
A 5-minute halftime compartment will have how much tissue pressure 5 minutes after taken from the surface to 18 metres depth?
After 5 minutes the compartment will go half way to saturation.
So if this is a 18m compartment, then half of 18m is 9m.
Answer = 9m of pressure 
To continue: After 10 minutes the pressure will go half way again.
Half the remaining 9m.  Half of 9m = 4.5m.
Add this to the first 9m (9m+4.5m) = 13.5m

M-VALUE

The M-Value is the MAXIMUM TISSUE PRESSURE (nitrogen level) that is allowed to be left in the body after a dive.
The faster the compartment, the shorter halftime.
The slower the compartment, the lower the M-value
The higher the M-value, the more nitrogen it is allowed to have upon surfacing.
The M-value represents what does and does not result in DCS.
These M-values are the A-Z on the RDP
A = a low level (low pressure) of nitrogen
Z = a high level (high pressure) of nitrogen.
At 12m our halftimes are shorter, so we can have a high M-value
E.g.  We can dive at 12m for 147 minutes = Z (M-value) 
At 30m our halftimes are longer so we have a low M-value
E.g.  We can dive at 30m for only 20 minutes = N (M-value) 
The compartment that reaches its M-value first, is called the CONTROLLING COMPARTMENT
WHY THE US NAVY (USN) TABLE WAS ‘STANDARD' FOR RECREATIONAL DIVING
The USN table was developed mainly for military decompression diving, but they became almost the standard in recreational diving until the mid-1980s for several reasons.   Before computers, developing a table was a difficult process that had to be calculated by hand.  Few outside the Navy had the information or the ability to produce tables.  Many early sport divers began as military divers, bringing the USN tables with them.  The USN tables were widely available in the public domain, allowing publishers to reproduce and re-arrange them.  Though they weren't ideal for recreational divers, they could be relied upon when following accepted conservative diving practices.

THE RDP TODAY - Dive Theory - RDP / Dive Tables

The RDP, as we know it today, was developed in 1987 and tested in 1988 by Dr. Raymond E Rogers (a PADI dive master) working with DSAT (Diving Science And Technology).

DIFFERENCES BETWEEN US NAVY TABLES & RDP

RDP
USN Table
NO–DECOMPRESSION (NO STOP)
STAGE DECOMPRESSION USE
14 Compartments
6 Compartments
60 minute surface credit
120 minute surface credit
Halftimes have faster gas washout
Halftimes have slower gas washout
6 hours to be clean of nitrogen
12 hours to be clean of nitrogen
Designed for multiple dives a day with a shorter surface interval (recreational diver)
Designed for limited dives a day with a longer surface interval (military use)
Longer bottom time on repetitive dives
Shorter bottom time on repetitive dives

HOW COMPUTERS COMPARE WITH EACH OTHER & THE RDP WITH RESPECT TO SURFACE INTERVAL & M-VALUES


Computers at times give longer no-decompression limits, because they 
Calculate the dive exactly
Eliminate unnecessary rounding (that you would do when using a table)

SPENCER LIMITS, EE WASHOUT

EE = ‘Exponential-Exponential'
Approximately the same M-value as the RDP
All compartments release theoretical nitrogen at the surface at their underwater halftime rate, as compared to the RDP, which releases theoretical nitrogen at the 60-minute rate for all compartments of 60 minutes or faster.  This washout means these computers can permit dives beyond what has been tested to work.  E.g.  3 dives to 40m in a row for 10 minutes each with only 30 minutes between them.  This washout is not a problem if divers avoid multiple deep dives with short surface intervals (generally not recommended whether using a computer or not)

SPENCER LIMITS, 60-MINUTE WASHOUT

Based on data for RDP
At the surface, all compartments 60 minutes and faster washout at 60 minute rate, all slower compartments wash out at their underwater halftime rate (like the RDP).
Dives very similar to what the RDP model allows.

BUHLMANN LIMITS, EE WASHOUT

Further reduced M-values (based on the work of Dr. Buhlmann) All compartments washout at their underwater halftime rate With reduced M-values repetitive dives similar to what the RDP supports, though repetitive deep dives with short surface intervals may still permit dives beyond what has been tested to work.  Spencer limits, 60-minute washout and Buhlmann limits, EE washout seem to be the most popular types of computers.

GENERAL RULES FOR USING THE RDP


PRESSURE GROUPS ON THE RDP

Letters (pressure groups) CANNOT be swapped (are not interchangeable) between the RDP, USN or any other tables.
You can link pressure groups between different versions of the RDP, such as the wheel and the enriched air 32% and 36% recreational dive planner.

COLD WATER DIVING

When planning a dive in cold water or under conditions that may be strenuous (difficult), plan the dive as if the depth is 4m deeper than actual.

REPETITIVE DIVES

Plan repetitive (2nd or 3rd) dives so each next dive is to the same, or a shallower depth.
Don't follow a dive with a deeper dive.
Max depth of 30m on repetitive dives
Plan your deepest dive first

LIMIT MAXIMUM DEPTHS TO TRAINING & EXPERIENCE

Discover Scuba Diver / Scuba Diver – 12m
Open Water Diver – 18m
Advanced Open Water / divers greater training and experience – 30m
40m is the maximum training depth for Deep Specialty Course
The 42m on the RDP is for emergency purposes only

SPECIAL RULES FOR SURFACING PRESSURE GROUPS

When planning 3 or more dives in a day:
If the ending pressure group after any dive is W or X the minimum surface interval between all next dives is 1 hour.
If the ending pressure group is Y or Z the minimum surface interval between all next dives is 3 hours Limit following dives to 30m / 100 feet or shallower

SAFETY STOPS

Make a safety stop for 3 minutes at 5m after every dive (recommended).  The time at a safety stop need not be added to the bottom time of the dive.
Always make a safety stop:
After any dive to 30m or deeper
Anytime you will surface within 3 pressure groups of your NDL
When a dive is made to any limit (black box) of the RDP

IN-WATER RECOMPRESSION

In-water recompression – treating DCI by putting the diver back underwater shouldn't be attempted.
Recompression takes a long time and requires oxygen and often drug therapy.
Normally the required resources aren't available at a dive site and incomplete recompression will usually make the diver even worse.

EMERGENCY DECOMPRESSION

An emergency decompression stop for 8 minutes at 5m must be made if a no-decompression limit is accidentally exceeded by 5 minutes or less.  Upon surfacing the diver must stay out of the water for at least 6 hours before making another dive.
If a no-decompression limit is exceeded by more than 5 minutes a 5m emergency decompression stop of no less than 15 minutes is needed (air supply permitting).  Upon surfacing the diver must remain out of the water for at least 24 hours before making another dive.

DEEPER THAN 40M?

If you accidentally go below 40m immediately ascend (18m per minute) to 5m and make an emergency decompression stop for 8 minutes. 
If the no-decompression limit for 40m is NOT exceeded by more  than  5 minutes.  Do not dive again for at least 6 hours.

MISSED DECOMPRESSION STOP

If you accidentally miss a required decompression stop and have already surfaced and exited the water, remain out of the water and stop diving for 24 hours and breath pure (100%) oxygen if available

DIVING AT ALTITUDE

Using the RDP at altitudes 300m above sea level requires the use of special training and procedures.
Add 4% to the depth for every 300m above sea level.  Conversion table is on page 15 in PADI Adventures In Diving manual.
Rule of thumb:- Subtract 0.035atm for each 300 m of altitude.
A lake is at 1800 m altitude.  A lift bag with 1 Lt of air inside is released from a depth of 10 m.  What will the air volume be on reaching the surface?
1800
--------  =  6 x 0.035  =  0.21atm  - 1 atm  = 0.79atm
300

Pressure at 10m  = 1atm + 0.79atm = 1.79atm
1.79 x 1 Lt of air
---------------------- = 2.26 lts
0.79
FLYING AFTER DIVING
A minimum surface interval of 12 hours is required before flying.  
If you make daily, multiple repetitive dives for several days, or make dives that require decompression stops a minimum surface interval of 18 hours is required before flying.

Recreational Dive Planning (RDP) - The Wheel revision

Single Depth Dives

Use the book that came with your wheel for practise and revision 
1st dive.            26 metres for 20 minutes
Side 1.
Put the white arrow onto 26 on the outer edge.
Put the yellow arrow onto 20.
Read the yellow PG index where it cuts the 26m curved line.  = PG = ‘L'.
Surface time 30 minutes.
Side 2.
Locate ‘L'.
Rotate wheel until 30 lines up with ‘L'.
Top of the white curved line = New PG ‘G'.
2nd dive.           24 metres for 15 minutes.
Side 1.
Move the white index until ‘G' touches the 24m curve.
Move the yellow arrow onto 15.
Read the yellow PG index where it cuts the 24m curved line.  = PG = ‘Q'.
3rd dive.            18 metres for 25 minutes.
Find the minimum surface interval? 
Side 1.
Line the Yellow index until it touches the NDL cross hatch of the 18m curve
Move the White index until 25 mins lines up with the Yellow arrow, follow the 18 m curve up and check which White letter touches the 18 m curve. In this case it is the letter L  
Side 2
Find the Q and then rotate until the top of the white line touches the bottom cross hatch for the L
Minimum Surface Interval time = 21 mins.


RECREATIONAL DIVE PLANNING ERDPML VERSION.

1st dive 26m for 20 mins
Turn on and make sure ERDPML is in metric mode.
Select ‘Dive Planning’ mode and press ENTER.
Multilevel ? Select NO, First Dive ? press YES
Enter Depth………Enter 26 m
NDL 27mins
Enter Actual Bottom Time……….20 mins
Pressure Group after dive “L”
Press Enter
Enter Surface Interval Time…………..30 mins and press enter 
PG after SI = G……press enter
2nd DIVE 24m for 15 mins
Enter Depth………Enter 24 m……press enter
Adjusted No Decompression Time ANDL 16 mins…….press enter
Enter Actual Bottom Time………..15 mins…….press enter
ERDPML should beep and flash warning of a safety stop, ( RULE 2 )
Press Enter ……Ending Pressure Group R
3rd DIVE 18m for 25 mins
FIND THE MINIMUM SURFACE INTERVAL
Select Surface Interval Mode….press Enter
First Dive Y/N……Enter No
Pressure Group end of Dive…….press number 7,3 times for R press enter
Enter Depth 2…….Enter 18m and press enter
ANDL = 50 mins……..press enter
Enter ABT2……….enter 25 mins……press enter
ERDPML should beep and flash warning of a safety stop,( RULE 2 ) press enter
Minimum Surface Interval = 30 mins

Multi-level Dives (Up to 3 different depth levels)


1st level 28 metres for 10 minutes.
As before.
Side 1.
Put the white arrow onto 28 on the outer edge.
Put the yellow arrow onto 10.
Read the yellow PG index where it cuts the 28m curved line.  = PG = ‘E'.
(Note maximum multi-level (ML) time is the same as the NDL time = 23 minutes).
By following the 28m curve read at the centre maximum 2nd depth is 20 metres.
2nd depth 18 metres for 15 minutes.
18 metres is below 20 so it is OK to continue.
Move the white index until ‘E' touches the 18m curve.
Move the yellow arrow onto 15.
Read the yellow PG index where it cuts the 18m curved line.  = PG = ‘M'.
(Note maximum multi-level (ML) time is 28 minutes).
By following the 18m curve read at the centre maximum 3rd depth is 12 metres.
3rd depth 10 metres for 20 minutes.
10 metres is below 12 so it is OK to continue.
Move the white index until ‘M' touches the 10m curve.
Move the yellow arrow onto 20.
Read the yellow PG index where it cuts the 10m curved line.  = PG = ‘Q'.
(Note maximum multi-level (ML) time is 131 minutes).

Multi-level Dives ERDPML (Up to 3 different depth levels)

1st level 28 meters for 10 mins
As before, turn on, select mode, Dive Planning, press enter.
Multi level Y/N?......press YES
First Dive Y/N?.......press Yes
Enter level………press 28m……..press enter
NDL = 23 mins…..press enter
Enter ABT………..enter 10 mins and press enter…PG = E after first level
2nd level 18 meters for 15 mins
Press enter
Enter level 2………enter 18m, press enter, ML = 29 mins……press enter.
Enter ABT……enter 15 mins and press enter
PG after level 2 = M……
3rd level 10meters for 20 mins
Press enter….
Enter level 3…..10 m and press enter…..ML = 130 mins….press enter
Enter ABT…….enter 20 mins….press enter
Pressure group after dive = Q
PLEASE NOTE THAT USING THE WHEEL THE NEXT DEEPEST DEPTH IS PRINTED ON THE ACTUAL WHEEL IN A YELLOW BOX AT THE CENTER OF THE WHEEL.
WHEN USING THE ERDPML YOU WILL HAVE TO ACCESS INSTRUCTIONS FOR USE BOOKLET PAGE 82.

Recreational Dive Planners (wheel, table, erdp)


1.         They are designed for recreational diving and use conservative limits to minimise bubble formation, even at levels that do not cause DCS.
2.         They were tested using Doppler technology not available when the Navy tables were developed.
3.         They contain more surface interval times for higher precision.
4.         They base surface interval elimination on half time that creates a realistic credit for surface intervals.
5.         The wheel / erdpml makes it possible to calculate multi-level dive times by giving credit for slower nitrogen uptake in shallow water.
6.         The wheel / erdpml allows the diver to more closely calculate time and depth profiles.

RDP Summary


Decompression theory is based on models and doesn't have any relationship with real people (but it's the best model we have so we rely on it)
All tables and computers are based on Haldanean decompression model, which are mathematical extrapolations.
First tables produced in 1906.
Different parts of the body absorb and release dissolved nitrogen at different rates.(different compartments / different halftimes)
Haldane's original model had 5 compartments, from 5 to 75 minutes, modern versions have 14 or more, ranging from 3 to more than 600 minutes.
Each compartment has a halftime for the rate at which it absorbs and releases nitrogen.
Halftime = the time in minutes, for a particular compartment to go halfway from its beginning tissue pressure to saturation at a new depth, in exponential progression.
After 6 halftimes the compartment is considered saturated (actually 98.6%).
The difference between the dissolved nitrogen pressure and the surrounding pressure (whether ascending or descending) is called the pressure gradient.
M-value = the maximum tissue pressure allowed in the compartment when surfacing to prevent exceeding acceptable gradients.  (in our diving we only use the one that applies at the surface).
The M-value is calculated for surfacing at sea level, at an altitude higher than 300m the gradient may be too high unless you use altitude diving procedures.
The US Navy used Haldane's tables and revised them periodically to meet changing needs.
The 1950 (current) US Navy tables had 2 important differences from the original Haldane model.
6 compartments were used with 120 minutes halftimes.
Surface interval credit added all divers in the previous 24 hours and were treated as one dive.
US Navy table were used until the mid 1980's because:-
Many early sport divers were ex Military.
The US table were available to the public.
They could be relied on.
The original US Navy tables designed its surface interval credit on the worst case 120 minutes halftime.  This is why, worst case, it take 12 hours to be clean.
In the mid 1980's Raymond Rogers a Divemaster recognised that the Navy tables might not be ideal for recreational diving.
The 120 minute surface interval credit was excessive for no-decompression dives.
The Navy tables were designed for males, fit and between 20 and 40 and not females etc.
Doppler ultrasound flow meters had not come into being.
During tests in 1987 and 1988 Rogers established:-
The 60 minute surface interval credit concept.
Extensive testing of multilevel diving.
Included a broader demographic test subjects.
The test were based on limiting Doppler detectable bubbles.
Multi-day testing successfully tested the RDP making 4 dives daily for 6 days.
Spencer 60 minute washout and Buhlmann EE washout seem to be the most popular types of computers

Skills and Environment


Skills and Environment


Waves

1.Capillary waves – very small.
2. Storm waves – large – 30 m +.
3. Wind causes waves.
4. Only the wave shape or energy moves.
5. The effects of the wave stops at a depth of 45m.
6. Waves are measured by height and length.
7. When a wave is as deep as its height, bottom friction slows the forward speed, it bunches up becomes higher / steeper then breaks.
8. They cause a ripple affect on the sand running parallel to the shore (handy for natural navigation)

Tides

1. Twice daily.
2. Tides result from gravitational interaction between the earth, sun and moon.  Also topographical features.
3. The moon has most effect.
4. Tidal wave results from seismic activity.

Currents

1.Coriolis effect – Northern Hemisphere – deflections to the right.
2.As a result water piles up in the middle of the pacific ocean.
3.Northern hemisphere trade winds blow from the NE to SW.
4.Currents negligible at depths of 190m.
5.Wind energy and the coriolis effect drives the ocean currents.
6. Northern hemisphere major ocean currents flow clockwise.
7.Southern hemisphere major ocean currents flow counter-clockwise.
8. The major current in the southern hemisphere turn: counterclockwise
9. Best time to diving: slack tide when high tides peaks
10. Currents are caused by wind and the earth's rotation
11. Tides are caused by: the gravitational interaction of the earth, moon and sun

Compass

1. Trust your compass: even if you think you are going to the wrong direction
2. Triangle: 120 degrees for each corner
3. Reciprocal heading on a compass means: 180 degrees from the initial heading
* Natural navigation, directional information: plants, animals, bottom composition (rocks, sand ripples…), light and shadow


Altitude Diving

1. RDP can be used using the Theoretical Depth at Altitude Chart from: 300 meters to 3000 meters
2. Ascent rate when diving in Altitude is: 9 meters per minute
3. If you want to do two dives in different altitude: the first must be in the highest altitude.
4. To use the RDP: only with special procedures
5. Altitude Diving: Capillary depth gauge
6. Planning an altitude dive: actual depths must converted to theoretical depths to find the pressure group
7. Special procedures:
- Nitrogen narcosis may occur at shallower depth
- The ambient atmospheric pressure at altitude is less than at sea level
- Actual depths must be converted to theoretical depths to find no decompression limits on the RDP



General information

1 CPR compression ratio for Adult, child and infant: 30/2
2 Use a lifting device, weight recommended: 4-7 kilos
3 Maximum depth for recreational diving is: 40m
4 CESA: must keep all the equipment in place, surfacing while emitting a continuous AHH sound
5 Recommendation for Safety Stops: at the end of every dives
6 Night Dives: one dive light but recommended that each divers 2 lights
7 Marine life injuries includes: respiratory depression or arrest, local swelling,
inflammation, severe pain, numbness, paralysis, cardiac arrest
8 Alternate air source: should be placed between the chin and the corners of your rib cage
9 Difference between DCS and Lung overexpansion is: DCS tends to appear a few hours after, Lung overexpansion upon surfacing

PADI Dive Theory Boat informationBoat Terminology

Front of the Boat is called the Bow
Back of the boat is called the Stern
Left is Port
Right is Starboard
Head is the Toilets
Galley is the Kitchen

 

 

Wind

Winward is towards the boat
Leeward is away from the boat (so if your feeling a bit unwell best stand Leeward)

Dive Theory - Equipment


Dive Theory - Equipment


tanks / cylinders - tank markings

1
Govt. Agency Supervision / Approval DOT or DOT/CTC = Dept. of Transport or Canadian Transport Comm. 
Metal Type: 3AA = Steel / SP6498, E6498 or 3AL = Aluminium 
Working Pressure: Maximum pressure lbs / inch2 (steel = 2250, al = 3000-4000 psi) 
Serial Number: 12345 = Unique to tank Manufacturer 
PST = Manufacturer of the Cylinder Hydrostatic Test Date / Hydrostatic Tester's Mark 
6 1996+ = Hydrostatic Test Date (Month, initials of tester, year)
+10% Overfill Allowed + = 10% overfill allowed on STEEL TANKS ONLY 
These marking should always be checked before filling. 
This is important even in different countries with different tank markings. 
Cylinders manufactured, have specification stamped on the cylinder which include Working Pressure, Test Pressure, Data of Manufacture, Capacity and Weight.
Before filling a scuba tank with air, you should always check the tank markings, specifically looking for a current hydrostatic and pressure test date and maximum capacity / pressure. Don’t overfill scuba cylinders.

tank metals


STEEL
ALUMINIUM
Resistance to corrosion
Quicker (lasts longer)
Slower
Galvanic Action
Brass values can react
Brass values can react

With steel (rust)
With Al. (Al. Oxide)
Weight
Heavier
Lighter
Size
Smaller (stronger)
Larger (less strong)
Buoyancy
Less buoyant (diver is not affected as tank pressure drops)
Can be more buoyant (more weight required as tank pressure drops)
Normal Working Pressure
200 Bar (300  Bar tec. Diving)
220 Bar
Hardness
Harder
Softer
Maintenance
Harder to clean
Easier to clean preferred by dive operators)
Availability
Less available
More available
Technical Diving
More popular (especially DIN)
Less popular
Bottom
Round
Flat

Cylinders

Kevlar wrapped composite cylinders or Carbon-Dive that can be filled up to 300bar and are very buoyant even when full. These are not common and must be treated with extreme care not to damage the carbon fibre Kevlar.

The Aluminium Tank with an International valve or DIN is the most common tank / valve combination in the world of visual inspection.
A visual inspection test are required by international laws (which may vary from country to country) conducted on all SCUBA tanks (steel and aluminium) at least once (1) a year. Never assume tank markings are unimportant on cylinders. In most European Union countries, visual inspection is required every 2 and half years, and a hydrostatic test every five years.

Visual Inspections

A visual inspection is conducted by removing the tank valve, looking inside the tank for any corrosion (steel tanks = IRON OXIDE - RUST / aluminium tanks = ALUMINIUM OXIDE). Iron oxide is orange or black and falls away from the tank, normally in layer like filo pastry. Visual inspections also examine the outside and inside of cylinders for defects like: bulges, gouges, misshapes, cracks, thickness, pitting and damages that could cause the cylinder to fail its test.
tank visual inspectionAluminium oxide tends to be of a white or gray powder most common found between the valve and the tank neck (galvanic action aluminium tanks). If there is any corrosion the tanks will be chemically and/or machined cleaned. If the corrosion has done damage to the walls of the inside of the tank, then pits and gouges must be measured with pit gauges or ultrasonic thickness testing devices to see if the corrosion is too deep, which will end the life of the cylinder and be destroyed.

The threading at the neck of the tank (where the tank valve screws into) is also inspected for any damage. First a precision threading gauge is inserted to test the threads for wear-n-tear. This thread test uses a GO – NO GO method, if more than a few turns on the no-go then the thread is considered worn and destroyed. This is a very important testing procedure for aluminium tanks as different types of aluminium's have been found to have weakness at this point. This could have occurred during manufacturing and/or over-pressurisation of a tank.
A testing method called None-Destructive-Testing (NDT) is done, using an EDDY current test machine. This is like an X-ray of the thread neck, checking for hair-line cracks. These cracks can be invisible to the naked eye but not the EDDY TESTER.

More Tanks Fail A Visual Than In Hydro Testing. Fact!

Hydrostatic Inspection

Hydrostatic inspection = water pressure test 
Laws differ from country to country 
US / UK- required every five years Elsewhere or according to local laws

A hydrostatic test is performed to ensure that the tank has no weak points and the metal still has elasticity in the body, and to make sure that the tank can withstand its own specific amount of high-pressure air used for diving.

A hydrostatic inspection is conducted by placing the tank in a pressure container filled with water. Then tank itself is filled with water, which will be used to pressurize the tank to approximately its own TEST pressure, NOT its working pressure which is less.
The use of water to pressurize the scuba cylinder is a much safer option than to pressurize with compressed air. Water is incompressible but compressed air will expands back to its original size, this would cause catastrophic damage to the cylinder, the hydro test chamber and the technician. Each cylinder and manufacturer has its own testing pressure of their tanks which is greater than its working pressure.
NOT ALL TEST AND WORKING PRESSURES ON EACH CYLINDER ARE THE SAME!

Afterwards the tank is checked for any damage or disfigurement (shape change) that may have occurred during the test. Certain circumstances can weaken tanks before a hydrostatic test is required.
Have tanks hydrostatically tested after exposure to any of the following:
  • Tumbling (or sandblasting) to remove corrosion.
  • Damage due to impact
  • Exposure to heat in excess of 82 degrees Celsius may affect the metals integrity.
  • If left unused for more than 2 years
  • Never paint a cylinder using a heat painting process such as that used on automobiles.

Tank valves

k valve or international valve
K valve are our modern tank valves. The K-valve is (kommon) a simple on – off valve that will open or close the tank pressure coming out of the tank opening. DIN Regulator screws into the tank valve and a YOKE, A-Clamp or an International fitting is a way your scuba regulator first stage attaches to the Tank Valve



j-valve
J valve (which are no longer used but are still found) are also called RESERVE VALVES. They were used before pressure gauges came into use for divers in the early 1970s that had NO SPG's when they dived. It's a spring-loaded valve on the scuba valve, which would close off a divers air supply once the pressure in the tank became low (between 40-60 Bar). The diver would then reach back or behind and
pull the pin or lever, which would then re-open the valve. It was used as an Early Warning Mechanism. The diver would then know that he had a RESERVE of air and had to make his way back to the surface.
When filling these tanks the pin or lever must be in the DOWN or OPEN position, to allow air back into the cylinder. If the lever is closed no air would fill the cylinder. If the lever would be left in the OPEN position, the diver would not have an early warning mechanism and when the diver began to find the regulator difficult to breath from it was the end of the air completely in the cylinder. These types of valves are rare but a understanding of the operation of these valves must be common knowledge for all divers.

din-valve
DIN (Deutsche Industrie Norm) German
 Has a stronger connection between the tank valve and the first stage of the regulator. DIN Valves Screw into the Valve and come in two types a short 5 threads so a tank can only be filled to 232 bar / 3364 psi and a long 7 threads and a tank can now be filled to 300 bar / 4351 psi. This only connection used when a tank is 300 bar / 4351 psi high tank pressure. These are the preferred valve by Wreck, Cave and Technical divers. The Regulator First Stage has the o-ring, the tank only has a hole with threads. Adaptors and insert can be found to cross convert for these valves.
  • Has a better seal.
  • Is stronger.
  • Can use higher air pressure
  • Preferred by Tech divers
  • Regulator has the o-ring as the tank does not have one
  • Can get adaptors to allow DIN regs on International Valves

NITROX DIN valves
, with a metric M 26×2 fittings are on both the cylinder and the first stage regulator. These are to be used with any oxygen content above 23%. From August 2008, these shall be required for all diving equipment used with nitrox or high oxygen contents in Europe. The idea behind this new standard is to prevent a rich oxygen mixture being filled in to a normal AIR (21%) cylinder and is not O2 clean. This is just a standard in Europe and not the rest of the world. So if you dived in Egypt, USA or Asia you would need an adaptor for your NITROX Regulator.
Burst Disk is a thin copper disk that is located on the valve and will break if the tank pressure becomes too high (140% of working pressure). Disks are replaced every year, due to weakening of disk from filling / emptying. Instead of the tank exploding the air will vent (come out) through the burst disk. Newer disks, which vent air from both sides prevents the spinning of cylinder regulators
We describe the 'most' common regulators in use as Open Circuit, Fail Safe and Balanced, which is open circuit scuba and typically used by recreational divers.
Open Circuit Scuba The diver inhales air from the cylinder via a demand valve regulator and exhales it into the water, thus the circuit is open because none of the air is recycled. Air is released into the open. When or should a typical regulator break, it will break in an open – free flowing action and will never break with a shut off of air, again it will break in an open action as long as air remains in the tank. Typical Open circuit doesn't recycle breathing gases; it is the main stay of recreational diving for many reasons:
  • It's a much simpler design, which makes it reliable and less costly (closed and semi-closed systems are more prone to malfunctions)
  • It requires only a cylinder of air (closed and semi-closed units require chemicals and access to pure gases or enriched air)
  • It is much easier to use
  • It is much simpler to maintain and service.

Semi-closed circuit scuba


The diver inhales from a breathing bag that receives a steady flow of gas (usually enriched air). 

Excess can gases steadily flows and trickles out through a valve in to the open. The circuit is semi-open because part of the gas is recycled and part of it is released (except to vent expanding air on ascent).

Closed circuit scuba

The diver exhales from a breathing bag and then exhales back into the breathing bag (Counter Lung). The gas has a Carbon dioxide scrubber and electronic sensors control flow of oxygen and other gases as required. The circuit is closed because ALL gases is recycled and none released (except to vent expanding air on ascent)

First stage


When high pressure (200 - 300 Bar) from a tank enters the first stage the first stage will do two things:
  • first stage regulator It will reduce the HIGH PRESSURE from the tank to between 9-12 Bar. This new pressure is called INTERMEDIATE PRESSURE.
  • The first stage will channel, or guide, the tank pressure to the HIGH-PRESSURE HOSE or a DIGITAL PRESSURE GAUGE (so that the diver can monitor tanks air pressure) which will contain an electronic transducer.
  • When the transducer feels pressure it will transmit a small amount of electric current, the more pressure exerted the more current.
  • The intermediate pressure will also go to the second stages and the low pressure inflator hose for the BCD


Second stage

3As a diver inhales the diaphragm at the front of the regulator flexes inwards. Air from the first stage moves downstream to the second stage, which will moved inward by the flex of the diaphragm and press down onto a lever. This allows intermediate/downstream pressure air coming from the first stage to enter the second stage where it will become AMBIENT / ABSOLUTE PRESSURE so that the diver may breathe. In more expensive regulators the lever opens a pilot valve, which in turn opens the main valve with the flow of air, a more complicated design that provides greater/better airflow with less breathing effort. In regulators with Upstream Valves the pilot valve moves against the airflow.

Second stages can be your primary regulator or your alternative air source or octopus. Your primary regulatorsecond stage regulatorhas a shorter hose around 24 inches/61 cm and should be less attractive to divers who may need air in the unlikely event of an emergency.

Alternative Air Source or Octopus is normally a brightly coloured yellow hose around 36 inches/91 cm. This regulator should be kept in plain view for other divers to see between your chin and the rib cage (triangular area). This is the regulator that you or another dive should take if they run low on air or their air suddenly stops.

 

 

Unbalanced


A regulator designed so that tank air pressure resists or assists (DOES AFFECT) the opening of valves in the first stage is called an unbalanced regulator:
  • Breathing will become more difficult as the tank pressure drops
  • Breathing is more difficult at greater depths
  • Unbalanced regulators are no longer commonly found
  • Unbalanced regulators are cheaper than balanced regulators.
  • Unbalanced regulators are perfect for recreational diving and NOT FOR DEEP DIVES

Balanced

A regulator designed so that tank air pressure neither resists nor assists (DOES NOT AFFECT) the opening of valves is called a balanced regulator. The tank pressure does not affect the ease of breathing, even when two divers breathe from the same first stage, and inhale at the same time. Depth is not a concern. Most modern regulators are balanced regulators. Balanced regulators are technical diver choice, as it will give a constant intermediate pressure regardless of depth or tank pressures.

Fail safe

Modern regulators are designed to free flow during a malfunction, which gives the regulator a fail-safe design. It will fail in a safe manner opening of air and continues to provide air until the tank is empty. Obviously the tank will lose air fast, so the diver must make an immediate ascent or take air provided from another air source.

Environmental seals

When diving in very cold water (such as cold water, deep diving or ice diving) the temperature drop can cause water to freeze around and inside the regulator first stage, freezing open valves, making free flowing of air. To avoid free flow in extremely cold water some regulator first stages have environmental sealing. This seal could contain silicone grease, oil or just air which doesn't freeze, around the first stage. The silicone, oil and air transmit the ambient pressure from the surrounding water to the diaphragm or piston in the regulator and function normally.
When diving in the cold air/water:
  • Only breathe from the regulator as you enter the water to avoid free flows.
  • Breathing from regulators in freezing condition, fast flowing air inside the first stage can freezing very quick.
  • If moisture is also contained in the breathing air from the cylinder this could also make the regulator free-flow.

Depth Gauges


CAPILLARY GAUGE

Capillary depth gauges are very inexpensive with a simple piece of clear tubing, sealed at one end and open at the other. When you dive the water goes in the tube by the ambient pressure. At 10m it is half the length of the tube, 20m a third, etc based on Boyle's Law. They are hard to read accurately at much deeper than 10m. Accurate and mainly used when diving at altitude.


OPEN BOURDON TUBE GAUGE

Open bourdon tube gauges contain a spiral shaped tube. Water enters the tube and increasing pressure causes the tube to straighten. The straightening of the tube moves small cogs and levers and the depth gauge needle moves on a dial at the face of the gauge. Because the tube is open, clogging can be a common problem with these devices.


OIL-FILLED GAUGE

Oil-filled gauges also use bourdon tube design, but using a sealed tube, oil filled gauge housing. Pressure transmitted through the oil causes the tube to coil more tightly. This moves the depth gauge needle. The depth gauge is not open to the water and therefore less prone to clogging.


DIAPHRAGM GAUGE

Diaphragm gauges function by connecting a flexible diaphragm to a series of levers and gears that mover the display needle. The use of a diaphragm avoids any clogging that would occur in a bourdon tube gauges


DIGITAL GAUGE

Digital Pressure Gauges are electronic gauges that can read depth or tank pressure with a electronic TRANSDUCER, which varies the electric current depending on the amount of pressure it receives, the more current the greater the pressure. It then transmits depending on the pressure to a digital display and you read the information. These offer the highest degree of accuracy and are used in dive computers and pressure transmitters to determine depth and pressure.
The most common problem with any electronic device is the event of malfunction, flood or failures. Batteries are the most common fault and you should take precaution and make sure this is not your primary computer, always have a back up table or computer.

SUBMERSIBLE PRESSURE GAUGE (SPG)

The SPG works on the same principle as the bourdon tube gauge. Electronic SPGs use a pressure transducer similar to those in dive computers / electronics of depth gauges. SPGs may be integrated with some dive computers. The most recent design of transducer is on the regulator first stage that transmits the air pressure to a wrist-worn computer, eliminating the SPG hose. The most common problem with all SPGs is failure to check them and running out of air.

COMPASSES

There is no easier place to get lost than in the underwater environment. Modern underwater compasses contain liquid filled to damped movement and to help withstand pressure. The needle is magnetic therefore always points North. Across the center of the compass you will find a Lubber line, which is your direction line you point or aim the compass to set your heading.
Now you point your compass to the direction you wish to head looking and aiming the lubber line in your intended direction, now you need to set the rotating bezel.
To set the rotating bezel, you rotate the outer ring found on the compass face so that you have the two index marks on the bezel set between the north needle. The single index marker on the bezel should now be on the South on the needle.
Now with the compass set you head off in your intended direction keeping the NORTH NEEDLE between you two index markers as you swim in a straight line and direction of the lubber line.
Reciprocal heading is a return heading back to where you just came. To do these just simply rotate yourself and NOT TOUCHING the compass. The north needle is pointing to the SINGLE index marker. This is your reciprocal heading make your return heading back to the point you just started.
Compass Bearings are numbers from 0 to 360. In the window on the compass as you swim, the number you see the line goes through is the bearing. If your compass doesn't contain a small window, it will be the number closest to you at the bottom of the lubber line.

OPTIONS FOR CARRYING GAUGES


Many experienced divers prefer instrument consoles wrist mounted gauges for simplicity and is the preferred and oldest method. Technical Divers like to have wrist mounted gauges, commonly on both wrist, if one hand is busy the other hand can keep an eye on the depth and information which is crucial information when Tech diving.

Your scuba regulator High Pressure hose from your first stage could have an Analogue Gauge Console which includes, oil-filled depth gauge, max-depth indicator and fits into a neat low-profile boot together with compact SPGs. Compasses can also be attached to these consoles to keep all your instruments in one place.

Please note: All gauges are a simple way of measuring a given pressure and cannot be relied on 100% unless calibrated. Use gauges as a gauge of indication to the amount shown. As with all Digital and Analogue follow manufactures recommendations and never take your readings as 100%.

Pressure

Atmospheric Pressure
The pressure exerted by the weight of the atmosphere at sea level.  It is 14.7 psi or 1 tm or 1 Bar.
Gauge Pressure
Is the pressure designation that uses atmospheric pressure as its zero point.  Expressed as ‘g' i.e. psig.
Absolute Pressure
Is a pressure that uses a vacuum as its zero point, or its equal to Atmospheric Pressure + Gauge Pressure.  Expressed as ‘a' i.e. psia or ata
Ambient Pressure
Same as Absolute Pressure
Hydrostatic Pressure
Water pressure
What is the absolute pressure (ata) at 18m in salt water ?
18m / 10m = 1.8 atm;   1.8 atm + 1 atm = 2.8 ata

IDC Guide Fact: The Aluminium Tank with an International valve is the most common tank / valve combination in the world

ENRICHED AIR DIVING CONSIDERATIONS


Equipment Considerations


Because enriched air has more oxygen than air has oxygen, there is a possible greater risk for fire or explosion related to equipment that has not been properly cleaned.

Industry guidelines involving equipment used with enriched air:
  • Most manufacturers require their equipment to be cleaned to oxygen service specifications if it will be exposed to more the 23 percent oxygen. The manufactures will void all warranties and hold you responsible for using this equipment above their recommendations.
  • When using 40 percent oxygen, or more, special oxygen cleaning and oxygen compatible materials are recommended. This is called the '40 percent rule'! Any piece of equipment that will be exposed to more than 40 percent oxygen requires special cleaning, lubrication and materials to meet oxygen service specifications. If such equipment is used with air from a standard source, it may need to be re-cleaned.
  • Follow the manufacturer's recommendations and guidelines with respect to using equipment with enriched air and oxygen.


Special Markings

A band around tank at least 15cm wide denoting that it contains ENRICHED AIR NITROX in Green and yellow. The top and bottom of the band should be a yellow 2.5cm band. The centre 10cm band should be green and contain the words 'Enriched Air', 'Enriched Air Nitrox', 'Nitrox', or similar. Yellow cylinders need only the green portion.
nitrox-markings

 

visual inspection stickerVisual Inspection Sticker stating the cylinder has been cleaned to oxygen service specifications. Depending on the dive shop or filling station, if you require a nitrox fill (22% O2 or more) they will ask for a dive certification and mix required. The fill station will check the cylinder for oxygen service sticker and a valid date. Also the oxygen contents will be checked for the correct mix of the last fill. If the contents analysed were 24% O2 and the last nitrox fill sticker says 32% O2? This tells the filler that it was filled with conventional air and could contaminate the cylinder. It is the discretion of the fill station to refuse a fill or advise the cylinder be cleaned (extra charge) before they fill it with your required nitrox (even if the final blend will have less than 40 percent oxygen).



nitrox filling stationDepending on the fill stations type of filling method for if the enriched, as different blending methods can vary from one fill station to another. Modern Nitrox Membrane Compressors can squeeze out nitrogen from its compressed air leaving a higher content of oxygen.


Continuous Gas Blending using a Nitrox Stick


The Nitrox Stick is a continuous blender using O2 tanks and a patented blending "Stik" to homogeneously mix air and pure oxygen at the inlet of a high-pressure air compressor. This is a specially designed stick and should not be attempted unless properly trained as a gas blender and fully understand the gas blending method and it potential hazards of use.


Partial Pressure Blending

This Blending method requires first putting pure oxygen into the cylinder, to around 29 bars of Pure Oxygen. The blender with the top off the mix with super-clean air via specially dedicated separate filters. The tank will be filled to around 210 bars depending on the tank. This filling method with allow the pure oxygen and the air to mix and should produce a 32% Mix.

Analyzing cylinders

A contents sticker or tag identifying the current blend, the fill date, the blends maximum depth (MOD) and the analyzer / divers name. The blender is only responsible for filling the tank, even if the mix you requested was wrong.
Enriched air divers must PERSONALLY ANALYZE the contents of their cylinders before using them. They are responsible for the air they breathe. On some dive boats its normal practice to grab any full cylinder available for the next dive – this isn't appropriate with enriched air, which practice calls for divers to use the tanks that they have personally analyzed. This is why the new European rule is for dedicated tanks that use oxygen above 22% must be fitted with a M26 valve.

What is a M26 Valve?

This is the type of scuba cylinder valve that must be fitted to any new cylinder that is going to be used with any gas greater than 22% oxygen; this is a European directive that came into force in August 2008. It looks similar to the Din type of valve, just slightly bigger and should have the information stamped or etched on the valve. This will match any regulator supplied in the European Union which has been designated for use with gas containing oxygen content greater than 22%.

In simple terms if you buy a new set of regulators for nitrox use they will come with a M26 fitting and if you buy a new cylinder for nitrox use then it will come fitted with a M26 valve. If you travel outside of Europe with your new M26 regulator, you will need a DIN adapter to convert one side to a standard DIN the other to allow your M26 regulator to fit.

What is technical diving?

When a technical diver is kitting up (getting their dive gear on), a set methodology and configuration of regulators, hoses and tanks in the dive team is required. Also because of different gasses, like high concentrations of oxygen and helium, this could be of potential hazards if placed on the wrong side of the diver or breathed at the wrong depths. With this in mind, you could be of little use to any technical diver other than assistance in lifting or passing of equipment.

Further Scuba Tank / Cylinder information